High Voltage
electric power transmission is > 35,000 volts and for safety AC > 1000 and DC > 1,500. AKA: HV
See Also: High Voltage Switching, High Voltage Meters, High Voltage Detectors, High Voltage Programmable Power Supplies, HV
-
product
32Ch Isolated Input Card
SET-1310
This card provides 32 optically isolated digital inputs. SET-1310 combines high-density IO with high isolation voltages and a wide input voltage range. It allows to break ground loops and protect your system from high-voltage spikes, but also to connect high voltage signals to standard logic level acquisition devices. The channel-to-channel isolation allows to connect signals from different DUTs to a single acquisition system without compromises.
-
product
Thick Film Heating Elements
GBR-200
GBR-200 series high voltage resistors are made in a thick film technology on ceramic substrates (Al2O3 96%). Those elements are used in high voltage applications requiring high stability and resistance.
-
product
PXI 2 Amp MUX, Dual 16-Channel 1-Pole
40-635-105
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
UltraCMOS SP12T RF Switch
PE42512
The PE42512 is a HaRP™ technology-enhanced absorptive SP12T RF switch that supports a frequency range from 9 kHz to 8 GHz. An external VSS pin is available for bypassing the internal negative voltage generator in order for the PE42512 to deliver spur-free performance. It delivers high isolation, low insertion loss and fast switching time, making this device ideal for filter bank switching and RF signal routing in test and measurement (T&M) and wireless applications up to 8 GHz. No blocking capacitors are required if DC voltage is not present on the RF ports.
-
product
Analogue (1kV below) Insulation Tester
1652 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on “low ohms” : 3Ω & 500Ω.● AC voltmeter with linear scale up to 600 Vac.● 200mA short circuit current for continuity.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display of external voltage presence.● Fuse, air gap, crowbar and overload protected.●...show more -
product
1U Rack Adapter for Series HSF-1U, HSF-1UR
RA 19
The 1U high rack adapter will mount four of the low profile 50W, 100W and 150W (Series HSF-1UR or HSF-1U) power supplies. Each plug-in power supply is equipped with a power on/off, indicator LEDs and voltage test points. The RA 19-1U provides access to the DIP switches and rack keying without disassembling the rack. It also provides a redundant scheme with modules 1 and 3 being powered from one a-c input and modules 2 and 4 from a second a-c input. Module numbering is left to right facing the front panel.
-
product
Light Intensity Meter
MT-4617
Measures the visible light produced by fluorescent lamp, metal-halide lamp, high voltage sodium lamp or electric incandescent lampBuilt-in precision photo diode sensor and color correction filterAutomatic and manual measured range switchingRelative and peak value measurementMeasures up to 200,000 lux / 20,000 FCExtra functions: Max./Min. value displayOver load indication/Low battery indicationAuto power offBacklightData hold, Zero calibration
-
product
Jumbo Display Digital Multimeter
HH2107
High Accuracy (Basic Accuracy 0.5%). Jumbo LCD display 2000 count, 21.8mm figure height. Manual Ranging at your choice (30 Range). High Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A. Resistance test up to 20MΩ. Diode test, audible continuity check and transistor test
-
product
Leeb Hardness Tester
THL210
LCD display of 128×64 matrix with back-light, showing all functions and parameters. Converts to all common hardness scales (HV,HB,HRC,HRB,HRA,HS). English displaying and easy and convenient menu operation. Powerful PC Software available and USB 1.0 interface and USB with Protective Membrane. 7 types of Impact Device optional, which don't need to be recalibrated when changing them. Memory of 600 groups data(impact times:32~1). Lower limit setting and sound alarm. Material of “cast steel” is added...show more -
product
High Voltage Pulse
For thicker coatings it has fully adjustable output voltage from 5 kilovolt to 25 kilovolts. For very demanding conditions, a sensitivity switch offers additional control.
-
product
Logic Analyzers
Verification and debug of today's high speed, low voltage digital signals requires probing solutions that can accurately acquire from a wide variety of electronic designs and protect signal fidelity. Tektronix logic analyzer probes contain a variety of connectivity options that are engineered to ensure that signal acquisition is a true reflection of your design's performance. Compare and learn more about Tektronix logic analyzer probe solutions.
-
product
Hi-Z HV Safety Voltmeters
B-1013-4
These Hi-Z® HV Safety Voltmeters are for Power Lines, Electric Cars, Electric Trolley and other High Voltage AC & DC detection and measurement. Emergency Crews can use these voltmeters to detect voltage presence warning. They will accurately measure AC and DC voltages.
-
product
Battery Cycler with Low Voltage/High Current Battery
9220
NHR’s Battery Cycler (9220) has low voltage and high current, designed for testing all battery chemistries including lead-acid, lead-cadmium, and other low voltage, high current, large format batteries (LFB) typically used in energy storage systems (ESS). This battery cycler is bi-directional requiring no additional equipment to charge or discharge the unit-under-test (UUT). Additionally, the built-in measurement system eliminates external measurement devices by providing time-stamped digital readings for voltage, current, power as well as Ah and kWh.
-
product
High Voltage Power Capacitors
Lifasa - International Capacitors, SA
Capacitors of correction power of cos φ and filtering of harmonics for AT of Lifasa, are manufactured under the base of the container / stainless steel box and porcelain terminals. There are two types, depending on the connection mode that we are going to use:*Single-phase (1 or 2 terminals) with internal fuses, for connection to the network through a double star. Recommended for networks of tension superior to 11 Kv or need of equipment of high power.*Three-phase (3 terminals) with internal fuses, for direct connection to three-phase network. Recommended for voltage networks lower than 11 Kv.
-
product
64-Ch 2A-250VAC 24VDC Mux/Matrix
YAV90059
The YAV90059 module can be configured in different ways depending the application needed: from 8-bank, 16-channel, 1 pole to 8-bank, 8-channel, 2 pole, or also 128 Channel 1-pole among other possibilities. It uses high quality electro-mechanical relays allowing each channel to switch current up to 2A and voltage up to 220VDC/250VAC.
-
product
FaithTech FTL 3000 Series Bench Linear Triple Channel DC Power Supply
FTL 3000 Series
Shenzhen FaithTech Technology Co., Ltd.
FTL 3000 series multichannel programmable Bench linear DC power supply provides high resolution, high accuracy and high stability. It also provides over voltage and over heat protection. It provides series and parallel operation modes with resolution up to 1mV/1mA.
-
product
Analog Clamp Tester (CE)
M-3000
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High accuracy analog display with strong taut band meter.*Meter lock function.*AC current, AC/DC voltage and resistance measurements.*Conform to IEC safety requirements.
-
product
PXI 2 Pole 18 way Mux with 2 Pole 18 way sen
40-658-002
This PXI multiplexer combines a 2-pole 18-way power distribution MUX with a second lower power 2-pole 18-way MUX in one convenient single slot PXI module.The module is ideal for power distribution where power and sense signals are required to be connected to an array of devices under test. This multiplexer is also convenient for making 4 wire low resistance measurements by supplying the resistor under test with high current through the power MUX and sensing the voltage drop through the sense MUX.
-
product
Professional Multimeter
Shenzhen UYIGAO Electronic Technology Co., Ltd
*This MultiMeter is a handheld digital multimeter, high reliability and portability, a perfect tool for the laboratory, factory and home.*It can measure AC/DC voltage, AC/DC current, resistance, capacitance, frequency, duty cycle, diode, continuity, NCV and temperature.*Moreover, more advantages such as backlight, data hold, auto range, true RMS, auto power off, low battery indication and over range indication.
-
product
Impulse Semiconductor High Current Integrated
Transmission Line Pulse Test System
The Impulse Semiconductor High Current Transmission Line Pulse (TLP) test system is the tool of choice for extracting ESD parameters for transient protection devices in a package, or at wafer level. With accuracy better than 100 milliohms at 40 amps peak current, the Impulse high current TLP is specially tailored to the needs of today's ESD device designers who must accurately measure low values dynamic resistance irrespective of breakdown voltage.
-
product
Cable Assy 37-Pin D-Type M/M 0.5m HV
40-970-037-0.5m-MM-HV
The 37-Pin D-Type High Voltage cable assembly is constructed from PTFE insulated 7/0.2 (24AWG) Tinned Copper Wire. Screwlocks are provided to secure the cable to its associated products. The 37-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
Analogue (1kV below) Insulation Tester
ST-1504
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Measures insulation(MΩ), continuity(Ω) and AC voltage.● Instant operation is possible with a push button, convenient timer is provided with automatic power off after three to five minutes to save the battery power.● LED (red) indication when testing insulation and continuity.● Use of a high efficiency and accurate DC-DC converter.● Most suitable for insulation resistance measurement of electrical household appliances, power line distribution and installation.
-
product
PXI Multiplexer, Very High Power DC, 4-Channel, 20A, 28V
40-664A-002
The multiplexer is suitable for switching heavy loads or for slave switching large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of DC voltage at high current.
-
product
Cable Fault Meter
A cable fault meter can locate open power cables, either live or dead (without current), with voltages up to 300 V. A cable fault meter can locate cables, circuits, short circuits and ground wires. To perform these functions, it is not always necessary to disconnect electrically sensitive devices or to disconnect the power from the cable which is being tested. Many cable fault meter devices can also locate ferrous and non-ferrous metals, wood and plastic with high degrees of accuracy.
-
product
Raptor HV High Voltage Tester
The Raptor-HV, also called the high voltage slave, is an optional product that extends the Raptor’s applications to tests that require the use of a moderately high AC voltage.
-
product
Reed Relays
TPM Reed Relays - surface mount, high breakdown voltage, high temperature operate, high density, miniature PCB through hole, standard PCB through hole, EMF low thermal, high insulation/dry, high insulation/wet, high insulation/high voltage, DIP/dual in-line package, SIP/single in-line package, multiplexer, and more.
-
product
Bridge Decking Testing Equipment
The testing process can detect blow holes, inclusions or thin areas in 'sprayed-type' membranes. Because the concrete contains a small amount of water, it is electrically conductive and a DC Pinhole Detector can be used to create a high voltage which is passed over the surface by the use of a brush electrode. An alarm will sound to identify any small defects which can be rectified so that the integrity of the coating can be verified.
-
product
Cable Assy 9-Pin D-Type, F/F, 1m, HV
40-970-009-1m-FF-HV
A 9-Pin D-Type Cable Assemby for general use constructed from PTFE Type C insulated wire. The connector assembly can be secured to the product by screwlocks.
-
product
RF COMPONENTS
If space is an issue and you are looking for high quality RF Components, ETL's wide range is designed and manufactured at the ETL factory. Covering DC to 40GHz, these are at the heart of many of our 19" Rack Systems.A key feature of many of ETL components is the ability to pass or block a 10 MHz signal or DC voltage through the products, which can be used to power interconnecting components or pass a stable frequency reference to a LNB or BUC within the system.